Last updated: November 22nd, 2019
Most of the time, Being able to dominate the landscape is a part of the thrill. There is nothing quite as exhilarating as rocketing through unexplored trails and navigating untamed brush. Sometimes, nature gets one over on you. Your hi lift jack which is neatly attached to the hi lift jack mount is what gets you out of most of those messes. If you are stuck in a tight place, you can winch yourself right out. Having one around is a must have, to keep you from being stranded out in the middle of nowhere.
It always takes heavy duty work so, Hi lift jack is massive probably steel and cast iron. These are heavy tools that you should not have bouncing around in your truck bed. If you hit uneven terrain or get into an accident, these jacks can become heavy projectiles.
You need to make sure you also have the high-quality hi lift jack mount to go with to safety. A hi Lift jack mount secures your jack safely to the hood of your vehicle, the truck bed or even on the roof rack. You will not need to worry that it will fall down while driving.
If you are looking for the peace of mind for your hi lift jack, a hi lift jack mount is best for you.
Best Hi-Lift Jack Mount
|Hi-Lift Jack TM-700/TM-750 Adjustable Tube Mount||Hi lift jack mount for jeep jk/CJ/YJ/TJ|
|Hi Lift Jack Mount 4X400 4XRAC Jack Mounting System||Hi Lift Jack Bumper Mount|
|Hi-Lift HM-800 Hood Mount||Hi Lift Jack Mount Jeep JK|
|BOLT 7028648 Hi-Lift Jack Mount for Jeep Wrangle||Hi Lift Jack Mount Jeep TJ & TK|
|Rugged Ridge 11586.01 Off-Road Jack Mount||Off-Road Jack Mount for 2007-2017 JK Jeeps|
What Type of Hi Lift Jack Mount?
The best advice is to secure your Hi-Lift jack mount anywhere except to the bottom of your vehicle. While some parts are easily stored underneath, when you need your jack the most, you are usually stuck in some rocky or muddy terrain. You will not want to crawl under the truck for it. There are different types of hi lift jack mount due to the installation location.
Hi Lift Jack Mount On The Bumper
Usually, the bumpers a design to lodge hi lift jack mount. It is easy to install, all you will need to do is to mount it on your Jeeps wrangler using bolts, some have brackets or have piece for mounting it. Off-road hi lift jack mount for Jeep Wrangler JK is stellar on the bumper.
Hi Lift Jack Mount On The Hood
The hi lift jack is mounted directly to existing hood hinge holes of your Jeep. they are easy to use and install, no need to drill holes. They are clean and look spectacular in your Jeep.
The Jeep is that there’s minimal space available to accommodate lengthy loads. This is an innovation that is making maximum use of options available in the exterior design of your Jeep. The hood can manage 32-62 inches of hi lift jack mount.
They are mostly built with aluminum, this makes them more durable. It’s good for off-road lovers to use hi lift jack on the hood.
Hi Lift Jack Mount At The Rear
like spare tires or reserve fuel tanks, the hi lift jack also is mounted on the rear door. this arrangement may also save space in some applications.
Hi Lift Jack Mount On The Side
Companies have gone high a notch high and come up with mounts which fits either on the left or right side of your Jeep. It is really cool to add the hi lift jack on the driver side of your Jeep. Add the rugged looking to your Jeep. This is one great Jeep accessories for Jeep lovers.
Hi Lift Jack Mount On bed truck
The several Mounting System allows convenient, secure mounting of a Hi-Lift jack to the inside of a pick-up bed. It can be mounted horizontally or vertically and used with or without a Jack Protector. Although designed to fit the bedrails of most pick-ups it can be used wherever a flat mounting surface is available. Lockable to deter theft.
Mounting a Hi Lift Jack to the Roll Bar
A few companies make mounts so you can place the jack somewhere on the roll bar. Usually on the rear section, out of your way. These seem to work best when you have a soft top, or no top at all. Typically the jack with bee mounted horizontally.
Hi Lift Jack Mount Tire Carrier
If you have a tire carrier on the back, especially if it’s a swing arm type, or it’s integral to the rear bumper, there are some other options to mount your hi lift jack there. The mount can be part of the bumper/swing arm, or just a bracket to attach to those pieces. The vertical position for the jack is used the most, but not always, depending on the manufacturer’s design.
Hi Lift Jack Mount Reviews
Hi lift jack mount for jeep jk/CJ/YJ/TJ
If you have the free tube on your 4×4, this is a great mount. With this kit, you can mount to roll cages, roof racks, roll bars, bull bars, and tube bumpers. Sometimes It easy to install on your rear tire carrier and holds your jack firmly and secure.
The brackets and knobs are made from 6061-T6 aluminum. the u-bolts, nuts, washers, and Hi Lift mounting studs are all stainless steel. This billet mount for a high lift Jack is made very well and is attractive to the eyes. Hold tight to rack and Jack.
The studs are 1/2” diameter so that means that your jack bar holes need to take at least a 1/2” bolt. The kit attaches to two tubing sizes:
The smaller kit (TM-700) is great for bull bars and roof racks that have smaller diameter tubing.
The larger kit (TM-750) is great for larger tubing on roll bars, roll cages, and tube bumpers. It comes with 2 pairs of bent U-bolts, one for smaller tubes and one for larger (I think it was 2-2.5″ and 2.5″-3″).It will fit roll bars on CJ/YJ/TJ/JK Jeeps with the padding removed
If you have little concerned about denting the tubes of the aluminum roof rack. To reduce the likelihood of this you can put a 6″ piece of automotive tubing (I think it was 1/2″ hot water tube) around the bolts before installation. it will help distribute the load a little and made installing and removing jack totally painless.
The knobs are large enough to operate with gloved hands. This hi lift mount will work with any hi lift or farm jack that can fit the jack mount studs.
If you’re really concerned with theft, you’ll want a locking device to deter theft.The u-bolt nuts are easy to remove with a wrench. You could secure the jack with a cable lock or u-lock but it would not be as clean. You could buy a locking knob and tack weld the nuts to the u-bolts, but welds make it very difficult to move or remove the mount in the future.
Hi Lift Jack Bumper Mount
The 4X400 4XRAC Jack Mounting System is a universal type mount that can be adapted to almost any type of bumper on any vehicle. These mount the jack in a horizontal position. Other mounts for the jacks are usually specific to a particular bumper from the manufacturers. The bumpers are either designed with the option of mounting a jack or have a bracket or piece that allows you to mount the jack to their bumpers. Usually, but not always, the jack will be in an upright position.
It comes with 2 mounting brackets, 2 mounting bracket caps, 2 wing nuts, 8 hex head cap screws, 8 lock nuts, 1 handle strap. It is designed to complete Heavy duty, 1/8 inch steel mounting brackets are slotted for adjustment. The brackets are made from 1/8” thick steel and have two holes in each bracket. If you don’t have a handle keeper, the velcro handle strap secures handle to jack bar. A thru hole in the carriage bolts allows placement of an owner supplied padlock for added security.
This hi lift jack mount is plenty strong, but it won’t be as corrosion-resistant as a mount with aluminum and stainless steel components.
A few installation tips:
- Don’t mount these brackets on plastic or hanging on thin metal. While mounting on top of a hood would be fine, mounting a hi lift to the side of your 4×4 would eventually fail. The sheet metal of the body is not strong enough to support that type of load. Eventually, the metal will fatigue, crack, and the jack will fall off. If you really needed the jack there, you’d have to weld in some reinforcement on the back of the body panel.
- Attach the brackets tightly to your jack, then mark the bracket holes. After you drill the first bracket’s holes, fit everything again and make sure your marks still line up. You don’t want to drill twice.
- If you have a Jeep and you care about it, this kit should not be your first choice. There are several Jeep-specific hi lift jack mounts that you should look at before drilling holes in your sheet metal.
Hi Lift Jack Mount Jeep JK
The Hi-Lift HM-800 Hood Mount is easy to install on any Jeep Wrangler JK. It mounts directly to existing hood hinge holes. This Hi-Lift Jack Hood Mount is made with structural anodized aluminum for strengths, durability, and a clean look.
This hi lift jack mount Fits 2007 to 2017 JK Wrangler, Rubicon and Unlimited include 2 and 4-door models machined from lightweight and strong 6061-T6 aluminum. It is designed and produced in the USA, makes it simple to securely mount a Hi-Lift jack in a readily accessible location – ready to use, and easy to get at when you need it.
The included plastic knobs are easy to use with gloved hands. They don’t lock, but you can buy one or two locking knobs and add them later if you need them.
This kit includes jack hood mount brackets, Installation hardware, and velcro strap.
If you’re really concerned with theft, the Hi-Lift HM-LK Hood Mount Locking Knob will bring peace of mind
But this kit does have some small issues. You won’t be able to flip your hood all the way back to the windshield. To do that, you’ll need to unbolt the jack first, then you can flip your hood all the way back. You can still open the hood and use the prop with the jack attached.
A few installation tips:
- Install one mount completely, then the other. This will keep you from having to realign your hood (this is not fun).
- The rubber pads go between the body and the bracket to protect your paint.
- If you think you can’t get your jack off your hood without scraping or dinging it, lay down a towel to protect your paint.
Hi Lift Jack Mount Jeep TJ & TK
The BOLT 7028648 Hi-Lift Jack Mount for Jeep Wrangle is a secure way to attach your high lift right to your jeep. It fit any JK and TJ model jeep in 1997 and beyond. It is really cool to add the hi lift jack on the driver side of your Jeep. Add the rugged looking to your Jeep.
The BOLT easy to Install, bolts into existing holes and don’t require drilling. once the mount is in place, it quick and easy to remove and mount your high lift. This kit comes with a jay bracket and instruction two bolts to lock washers, two flat washers, a plastic gasket, two plastic knobs, and a bolt receiver head.
Features an innovative technology that allows you to set a wide variety of locks
to work with your Jeep’s ignition key. It’s the perfect blend of convenience and security. Programming your ignition key to work with a BOLT lock is as simple as it gets. Just insert the ignition key into the BOLT lock, turn it once and the lock mechanically and permanently learns the key code. Be careful as the BOLT locks permanently learn the first key used on them and cannot be reset. This is done for added security.
Convenience isn’t the only benefit with BOLT locks. BOLT locks are made by STRATTEC, the world’s largest manufacturer of automotive locks and keys. They are the main OE lock supplier for Ford, GM, and Chrysler. Because BOLT locks use automotive technology and materials, they have the highest corrosion resistance rating on the market.
Another added benefit is that they are nearly impossible to pick because of its patented 6 Plate Tumbler Sidebar technology. The lock features a solid zinc core and stainless steel lock shutter to keep dirt and moisture. In addition to, the J mount also comes with a lifetime warranty.
Off-Road Jack Mount for 2007-2017 JK Jeeps
The Rugged Ridge Off-Road Jack Mount allows you to carry your Off-Road jack on the outside of your vehicle saving precious cargo space. Fast and easy bolt-on installation. Compatible with stock and most aftermarket rear bumpers (without tire carriers) as well as Rugged Ridge XHD rear bumper with or without tire carrier. The bracket is sturdy and secures the jack in two locations to eliminate any vibration noise during vehicle operation. Durable textured finish looks great. Fits most off-road style jacks including Hi-Lift.
We like the placement because it puts the jack out of the way. Compared to a hood mount, this won’t block your view out the windshield, it won’t block your washer nozzles, and it’s easier to put on and take off without worrying about your paint.
It really is a smart mount, the weight of the jack rests on the bracket, so the bolts that hold the jack in place only hold it in place – they don’t experience any shear forces as they would if the jack hung from the bolts in this position.
A 48” jack will stick up above the roofline on your JK by a few inches. If you’re an East Coast or PNW wheeler where trails are tight, you might have an issue with branches catching on the jack. On the other hand, this usually isn’t a problem on established trails, and you might already be rocking a tree-snagging roof rack.
Factor When to Choose Hi lift Jack Mount
The Location Is Key
There are several factors that put in place when choosing mounting systems. The material has to be corrosion free. This is because off-road Jeep usually traverses through rocky areas. In the process, there are collision and rubbing of hi lift jack mount.
Where you decide to put the hi lift jack is something to consider carefully. On bed truck? On the side right or left? At The Rear? Or in another location that makes it the focal point of the car? If you do end up putting its front hood. It mounts directly to your existing hood hinge holes. So there’s no drilling or fabrication needed. This is a popular mounting spot since it’s always visible and out of the way.
Materials and Corrosion
When selecting a hi lift jack mount it is important to take into consideration the materials used in its construction. While some materials may be an up-front low-cost option, if they are used in the wrong application it can become more expensive in the long-term due to premature failure.
Depending on your use, think about the materials and finishes in the mount. Stainless steel and aluminum will never rust. While mounts and hardware that are made of plain steel will eventually rust and the jack will inevitably rattle on the mount at some point, or you’ll bang the mount with the jack.
Some mounts lock and some don’t. Some use a knob lock and some allow you to use a small padlock. Most knob locks from recognized brands are very resistant to the weather and won’t be difficult to open after they’ve been on your 4×4 for a while.
Their internal components are made of non-corroding stainless steel and aluminum. On the other hand, if you buy a cheap padlock to secure your hi lift jack, it’ll probably rust internally making it difficult or impossible to get at your hi lift when you need it most.